Pushrod help?

[ignoramus]

Guys, since the forum's a bit slow, I decided to put this is the humour section.
I'd like to hear opinions from non-car people!

OK, so I'm looking into beefing up the top end.
With the new roller rockers, I'll obviously need to use guide plates as well.
But everyone knows that guide plates can wear out standard factory pushrods, so I need the hardened variety.

I'm torn between plain 3 piece hardened pushrods which will do the job or should I pay $100 extra for chrome moly 1 piece pushrods?

All opinions are welcome...

[brewer]

Titanium with hardened inserts.

Edit: I have no fucking clue.

[Fireball]

Guys, since the forum's a bit slow, I decided to put this is the humour section.
I'd like to hear opinions from non-car people!

OK, so I'm looking into beefing up the top end.
With the new roller rockers, I'll obviously need to use guide plates as well.
But everyone knows that guide plates can wear out standard factory pushrods, so I need the hardened variety.

I'm torn between plain 3 piece hardened pushrods which will do the job or should I pay $100 extra for chrome moly 1 piece pushrods?

All opinions are welcome...

Feckin' Fords.  Doesn't your engine have a rocker arm shaft? If not, maybe you can find some Teflon® kit to minimize the abrasion from the guide plates.

[ignoramus]

(can't get shaft for canted valve clevos!)

Brewer wins so far for best sounding answer! lol

keep 'em coming! C'mon girls!

[vulcanlogician]

[vorlon13]

[ignoramus]

Shit V, now you're scaring away the passerby's!

[LadyForCamus]

Guys, since the forum's a bit slow, I decided to put this is the humour section.
I'd like to hear opinions from non-car people!

OK, so I'm looking into beefing up the top end.
With the new roller rockers, I'll obviously need to use guide plates as well.
But everyone knows that guide plates can wear out standard factory pushrods, so I need the hardened variety.

I'm torn between plain 3 piece hardened pushrods which will do the job or should I pay $100 extra for chrome moly 1 piece pushrods?

All opinions are welcome...

I think hard rods will usually get the job done, imo.  It’s very important that you always push the rod deep into the top end.  The bottom end...well, that doesn’t work on all models. You’ve got to know how to rock and roll well enough without involving the bottom end, which takes some practice.  Beef up under the hood wherever you can, for as long as possible, and don’t forget your gear oil. lubrication is crucial. Finally, when choosing between three hard rods, always go for sturdiness rather than length.  And, a little extra cash can always get you what you want.

[Fireball]

(can't get shaft for canted valve clevos!)

Brewer wins so far for best sounding answer! lol

keep 'em coming! C'mon girls!

Too true. I don't have rocker arm shafts on my Big Block Chevy.

---

LadyForCamus

Guys, since the forum's a bit slow, I decided to put this is the humour section.
I'd like to hear opinions from non-car people!

OK, so I'm looking into beefing up the top end.
With the new roller rockers, I'll obviously need to use guide plates as well.
But everyone knows that guide plates can wear out standard factory pushrods, so I need the hardened variety.

I'm torn between plain 3 piece hardened pushrods which will do the job or should I pay $100 extra for chrome moly 1 piece pushrods?

All opinions are welcome...

I think hard rods will usually get the job done, imo.  It’s very important that you always push the rod deep into the top end.  The bottom end...well, that doesn’t work on all models. You’ve got to know how to rock and roll well enough without involving the bottom end, which takes some practice.  Beef up under the hood wherever you can, for as long as possible, and don’t forget your gear oil. lubrication is crucial. Finally, when choosing between three hard rods, always go for sturdiness rather than length.  And, a little extra cash can always get you what you want.

Dayamn, you are funny, for not being a car person...or ARE you!? :brow:

[ignoramus]

Fireball. I think she's on the plonk again! Everything's about sex when you're drunk! lol!

My next post was going to be about putting a girdle on to reinforce the bottom end, but now I'm not so sure!